W3cubDocs

vyos_interfaces – Manages interface attributes of VyOS network devices

New in version 2.9.

Synopsis
Parameters
Notes
Examples
Return Values
Status

Synopsis

This module manages the interface attributes on VyOS network devices.
This module supports managing base attributes of Ethernet, Bonding, VXLAN, Loopback and Virtual Tunnel Interfaces.

Parameters

Parameter			Choices/Defaults	Comments
config list				The provided interfaces configuration.
	description string			Interface description.
	duplex string		Choices: full half auto	Interface duplex mode. Applicable for Ethernet interfaces only.
	enabled boolean		Choices: no yes ←	Administrative state of the interface. Set the value to `true` to administratively enable the interface or `false` to disable it.
	mtu integer			MTU for a specific interface. Refer to vendor documentation for valid values. Applicable for Ethernet, Bonding, VXLAN and Virtual Tunnel interfaces.
	name string / required			Full name of the interface, e.g. eth0, eth1, bond0, vti1, vxlan2.
	speed string		Choices: auto 10 100 1000 2500 10000	Interface link speed. Applicable for Ethernet interfaces only.
	vifs list			Virtual sub-interfaces related configuration. 802.1Q VLAN interfaces are represented as virtual sub-interfaces in VyOS.
		description string		Virtual sub-interface description.
		enabled boolean	Choices: no yes ←	Administrative state of the virtual sub-interface. Set the value to `true` to administratively enable the interface or `false` to disable it.
		mtu integer		MTU for the virtual sub-interface. Refer to vendor documentation for valid values.
		vlan_id integer		Identifier for the virtual sub-interface.
state string			Choices: merged ← replaced overridden deleted	The state of the configuration after module completion.

Notes

Note

Tested against VyOS 1.1.8 (helium).
This module works with connection network_cli. See the VyOS OS Platform Options.

Examples

# Using merged
#
# -------------
# Before state:
# -------------
#
# vyos@vyos:~$ show configuration commands | grep interfaces
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 address 'dhcpv6'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 hw-id '08:00:27:ea:0f:b9'
# set interfaces ethernet eth1 smp-affinity 'auto'
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth2 smp-affinity 'auto'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces loopback lo

- name: Merge provided configuration with device configuration
  vyos_interfaces:
    config:
      - name: eth2
        description: 'Configured by Ansible'
        enabled: True
        vifs:
          - vlan_id: 200
            description: "VIF 200 - ETH2"

      - name: eth3
        description: 'Configured by Ansible'
        mtu: 1500

      - name: bond1
        description: 'Bond - 1'
        mtu: 1200

      - name: vti2
        description: 'VTI - 2'
        enabled: false
    state: merged
#
#
# -------------------------
# Module Execution Result
# -------------------------
#
# "before": [
#           {
#            "enabled": true,
#            "name": "lo"
#           },
#       {
#            "enabled": true,
#            "name": "eth3"
#        },
#        {
#            "enabled": true,
#            "name": "eth2"
#        },
#        {
#            "enabled": true,
#            "name": "eth1"
#        },
#        {
#            "duplex": "auto",
#            "enabled": true,
#            "name": "eth0",
#            "speed": "auto"
#        }
#    ]
#
# "commands": [
#        "set interfaces ethernet eth2 description 'Configured by Ansible'",
#        "set interfaces ethernet eth2 vif 200",
#        "set interfaces ethernet eth2 vif 200 description 'VIF 200 - ETH2'",
#        "set interfaces ethernet eth3 description 'Configured by Ansible'",
#        "set interfaces ethernet eth3 mtu '1500'",
#        "set interfaces bonding bond1",
#        "set interfaces bonding bond1 description 'Bond - 1'",
#        "set interfaces bonding bond1 mtu '1200'",
#        "set interfaces vti vti2",
#        "set interfaces vti vti2 description 'VTI - 2'",
#        "set interfaces vti vti2 disable"
#    ]
#
# "after": [
#        {
#            "description": "Bond - 1",
#            "enabled": true,
#            "mtu": 1200,
#            "name": "bond1"
#        },
#        {
#            "enabled": true,
#            "name": "lo"
#        },
#        {
#            "description": "VTI - 2",
#            "enabled": false,
#            "name": "vti2"
#        },
#        {
#            "description": "Configured by Ansible",
#            "enabled": true,
#            "mtu": 1500,
#            "name": "eth3"
#        },
#        {
#            "description": "Configured by Ansible",
#            "enabled": true,
#            "name": "eth2",
#            "vifs": [
#                {
#                    "description": "VIF 200 - ETH2",
#                    "enabled": true,
#                    "vlan_id": "200"
#                }
#            ]
#        },
#        {
#            "enabled": true,
#            "name": "eth1"
#        },
#        {
#            "duplex": "auto",
#            "enabled": true,
#            "name": "eth0",
#            "speed": "auto"
#        }
#    ]
#
#
# -------------
# After state:
# -------------
#
# vyos@vyos:~$ show configuration commands | grep interfaces
# set interfaces bonding bond1 description 'Bond - 1'
# set interfaces bonding bond1 mtu '1200'
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 address 'dhcpv6'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 hw-id '08:00:27:ea:0f:b9'
# set interfaces ethernet eth1 smp-affinity 'auto'
# set interfaces ethernet eth2 description 'Configured by Ansible'
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth2 smp-affinity 'auto'
# set interfaces ethernet eth2 vif 200 description 'VIF 200 - ETH2'
# set interfaces ethernet eth3 description 'Configured by Ansible'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces ethernet eth3 mtu '1500'
# set interfaces loopback lo
# set interfaces vti vti2 description 'VTI - 2'
# set interfaces vti vti2 disable
#


# Using replaced
#
# -------------
# Before state:
# -------------
#
# vyos:~$ show configuration commands | grep eth
# set interfaces bonding bond1 description 'Bond - 1'
# set interfaces bonding bond1 mtu '1400'
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 description 'Management Interface for the Appliance'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:f3:6c:b5'
# set interfaces ethernet eth0 smp_affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 description 'Configured by Ansible Eng Team'
# set interfaces ethernet eth1 duplex 'full'
# set interfaces ethernet eth1 hw-id '08:00:27:ad:ef:65'
# set interfaces ethernet eth1 smp_affinity 'auto'
# set interfaces ethernet eth1 speed '100'
# set interfaces ethernet eth2 description 'Configured by Ansible'
# set interfaces ethernet eth2 duplex 'full'
# set interfaces ethernet eth2 hw-id '08:00:27:ab:4e:79'
# set interfaces ethernet eth2 mtu '500'
# set interfaces ethernet eth2 smp_affinity 'auto'
# set interfaces ethernet eth2 speed '100'
# set interfaces ethernet eth2 vif 200 description 'Configured by Ansible'
# set interfaces ethernet eth3 description 'Configured by Ansible'
# set interfaces ethernet eth3 duplex 'full'
# set interfaces ethernet eth3 hw-id '08:00:27:17:3c:85'
# set interfaces ethernet eth3 mtu '1500'
# set interfaces ethernet eth3 smp_affinity 'auto'
# set interfaces ethernet eth3 speed '100'
# set interfaces loopback lo
#
#
- name: Replace device configurations of listed interfaces with provided configurations
  vyos_interfaces:
    config:
      - name: eth2
        description: "Replaced by Ansible"

      - name: eth3
        description: "Replaced by Ansible"

      - name: eth1
        description: "Replaced by Ansible"
    state: replaced
#
#
# -----------------------
# Module Execution Result
# -----------------------
#
# "before": [
#        {
#            "description": "Bond - 1",
#            "enabled": true,
#            "mtu": 1400,
#            "name": "bond1"
#        },
#        {
#            "enabled": true,
#            "name": "lo"
#        },
#        {
#            "description": "Configured by Ansible",
#            "duplex": "full",
#            "enabled": true,
#            "mtu": 1500,
#            "name": "eth3",
#            "speed": "100"
#        },
#        {
#            "description": "Configured by Ansible",
#            "duplex": "full",
#            "enabled": true,
#            "mtu": 500,
#            "name": "eth2",
#            "speed": "100",
#            "vifs": [
#                {
#                    "description": "VIF 200 - ETH2",
#                    "enabled": true,
#                    "vlan_id": "200"
#                }
#            ]
#        },
#        {
#            "description": "Configured by Ansible Eng Team",
#            "duplex": "full",
#            "enabled": true,
#            "name": "eth1",
#            "speed": "100"
#        },
#        {
#            "description": "Management Interface for the Appliance",
#            "duplex": "auto",
#            "enabled": true,
#            "name": "eth0",
#            "speed": "auto"
#        }
#    ]
#
# "commands": [
#        "delete interfaces ethernet eth2 speed",
#        "delete interfaces ethernet eth2 duplex",
#        "delete interfaces ethernet eth2 mtu",
#        "delete interfaces ethernet eth2 vif 200 description",
#        "set interfaces ethernet eth2 description 'Replaced by Ansible'",
#        "delete interfaces ethernet eth3 speed",
#        "delete interfaces ethernet eth3 duplex",
#        "delete interfaces ethernet eth3 mtu",
#        "set interfaces ethernet eth3 description 'Replaced by Ansible'",
#        "delete interfaces ethernet eth1 speed",
#        "delete interfaces ethernet eth1 duplex",
#        "set interfaces ethernet eth1 description 'Replaced by Ansible'"
#    ]
#
# "after": [
#        {
#            "description": "Bond - 1",
#            "enabled": true,
#            "mtu": 1400,
#            "name": "bond1"
#        },
#        {
#            "enabled": true,
#            "name": "lo"
#        },
#        {
#            "description": "Replaced by Ansible",
#            "enabled": true,
#            "name": "eth3"
#        },
#        {
#            "description": "Replaced by Ansible",
#            "enabled": true,
#            "name": "eth2",
#            "vifs": [
#                {
#                    "enabled": true,
#                    "vlan_id": "200"
#                }
#            ]
#        },
#        {
#            "description": "Replaced by Ansible",
#            "enabled": true,
#            "name": "eth1"
#        },
#        {
#            "description": "Management Interface for the Appliance",
#            "duplex": "auto",
#            "enabled": true,
#            "name": "eth0",
#            "speed": "auto"
#        }
#    ]
#
#
# -------------
# After state:
# -------------
#
# vyos@vyos:~$ show configuration commands | grep interfaces
# set interfaces bonding bond1 description 'Bond - 1'
# set interfaces bonding bond1 mtu '1400'
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 address 'dhcpv6'
# set interfaces ethernet eth0 description 'Management Interface for the Appliance'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 description 'Replaced by Ansible'
# set interfaces ethernet eth1 hw-id '08:00:27:ea:0f:b9'
# set interfaces ethernet eth1 smp-affinity 'auto'
# set interfaces ethernet eth2 description 'Replaced by Ansible'
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth2 smp-affinity 'auto'
# set interfaces ethernet eth2 vif 200
# set interfaces ethernet eth3 description 'Replaced by Ansible'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces loopback lo
#
#
# Using overridden
#
#
# --------------
# Before state
# --------------
#
# vyos@vyos:~$ show configuration commands | grep interfaces
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 address 'dhcpv6'
# set interfaces ethernet eth0 description 'Ethernet Interface - 0'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 mtu '1200'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 description 'Configured by Ansible Eng Team'
# set interfaces ethernet eth1 hw-id '08:00:27:ea:0f:b9'
# set interfaces ethernet eth1 mtu '100'
# set interfaces ethernet eth1 smp-affinity 'auto'
# set interfaces ethernet eth1 vif 100 description 'VIF 100 - ETH1'
# set interfaces ethernet eth1 vif 100 disable
# set interfaces ethernet eth2 description 'Configured by Ansible Team (Admin Down)'
# set interfaces ethernet eth2 disable
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth2 mtu '600'
# set interfaces ethernet eth2 smp-affinity 'auto'
# set interfaces ethernet eth3 description 'Configured by Ansible Network'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces loopback lo
# set interfaces vti vti1 description 'Virtual Tunnel Interface - 1'
# set interfaces vti vti1 mtu '68'
#
#
- name: Overrides all device configuration with provided configuration
  vyos_interfaces:
    config:
      - name: eth0
        description: Outbound Interface For The Appliance
        speed: auto
        duplex: auto

      - name: eth2
        speed: auto
        duplex: auto

      - name: eth3
        mtu: 1200
    state: overridden
#
#
# ------------------------
# Module Execution Result
# ------------------------
#
# "before": [
#        {
#            "enabled": true,
#            "name": "lo"
#        },
#        {
#            "description": "Virtual Tunnel Interface - 1",
#            "enabled": true,
#            "mtu": 68,
#            "name": "vti1"
#        },
#        {
#            "description": "Configured by Ansible Network",
#            "enabled": true,
#            "name": "eth3"
#        },
#        {
#            "description": "Configured by Ansible Team (Admin Down)",
#            "enabled": false,
#            "mtu": 600,
#            "name": "eth2"
#        },
#        {
#            "description": "Configured by Ansible Eng Team",
#            "enabled": true,
#            "mtu": 100,
#            "name": "eth1",
#            "vifs": [
#                {
#                    "description": "VIF 100 - ETH1",
#                    "enabled": false,
#                    "vlan_id": "100"
#                }
#            ]
#        },
#        {
#            "description": "Ethernet Interface - 0",
#            "duplex": "auto",
#            "enabled": true,
#            "mtu": 1200,
#            "name": "eth0",
#            "speed": "auto"
#        }
#    ]
#
# "commands": [
#        "delete interfaces vti vti1 description",
#        "delete interfaces vti vti1 mtu",
#        "delete interfaces ethernet eth1 description",
#        "delete interfaces ethernet eth1 mtu",
#        "delete interfaces ethernet eth1 vif 100 description",
#        "delete interfaces ethernet eth1 vif 100 disable",
#        "delete interfaces ethernet eth0 mtu",
#        "set interfaces ethernet eth0 description 'Outbound Interface For The Appliance'",
#        "delete interfaces ethernet eth2 description",
#        "delete interfaces ethernet eth2 mtu",
#        "set interfaces ethernet eth2 duplex 'auto'",
#        "delete interfaces ethernet eth2 disable",
#        "set interfaces ethernet eth2 speed 'auto'",
#        "delete interfaces ethernet eth3 description",
#        "set interfaces ethernet eth3 mtu '1200'"
#    ],
#
# "after": [
#        {
#            "enabled": true,
#            "name": "lo"
#        },
#        {
#            "enabled": true,
#            "name": "vti1"
#        },
#        {
#            "enabled": true,
#            "mtu": 1200,
#            "name": "eth3"
#        },
#        {
#            "duplex": "auto",
#            "enabled": true,
#            "name": "eth2",
#            "speed": "auto"
#        },
#        {
#            "enabled": true,
#            "name": "eth1",
#            "vifs": [
#                {
#                    "enabled": true,
#                    "vlan_id": "100"
#                }
#            ]
#        },
#        {
#            "description": "Outbound Interface For The Appliance",
#            "duplex": "auto",
#            "enabled": true,
#            "name": "eth0",
#            "speed": "auto"
#        }
#    ]
#
#
# ------------
# After state
# ------------
#
# vyos@vyos:~$ show configuration commands | grep interfaces
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 address 'dhcpv6'
# set interfaces ethernet eth0 description 'Outbound Interface For The Appliance'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 hw-id '08:00:27:ea:0f:b9'
# set interfaces ethernet eth1 smp-affinity 'auto'
# set interfaces ethernet eth1 vif 100
# set interfaces ethernet eth2 duplex 'auto'
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth2 smp-affinity 'auto'
# set interfaces ethernet eth2 speed 'auto'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces ethernet eth3 mtu '1200'
# set interfaces loopback lo
# set interfaces vti vti1
#
#
# Using deleted
#
#
# -------------
# Before state
# -------------
#
# vyos@vyos:~$ show configuration commands | grep interfaces
# set interfaces bonding bond0 mtu '1300'
# set interfaces bonding bond1 description 'LAG - 1'
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 address 'dhcpv6'
# set interfaces ethernet eth0 description 'Outbound Interface for this appliance'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 description 'Configured by Ansible Network'
# set interfaces ethernet eth1 duplex 'full'
# set interfaces ethernet eth1 hw-id '08:00:27:ea:0f:b9'
# set interfaces ethernet eth1 smp-affinity 'auto'
# set interfaces ethernet eth1 speed '100'
# set interfaces ethernet eth2 description 'Configured by Ansible'
# set interfaces ethernet eth2 disable
# set interfaces ethernet eth2 duplex 'full'
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth2 mtu '600'
# set interfaces ethernet eth2 smp-affinity 'auto'
# set interfaces ethernet eth2 speed '100'
# set interfaces ethernet eth3 description 'Configured by Ansible Network'
# set interfaces ethernet eth3 duplex 'full'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces ethernet eth3 speed '100'
# set interfaces loopback lo
#
#
- name: Delete attributes of given interfaces (Note - This won't delete the interfaces themselves)
  vyos_interfaces:
    config:
      - name: bond1

      - name: eth1

      - name: eth2

      - name: eth3
    state: deleted
#
#
# ------------------------
# Module Execution Results
# ------------------------
#
# "before": [
#        {
#            "enabled": true,
#            "mtu": 1300,
#            "name": "bond0"
#        },
#        {
#            "description": "LAG - 1",
#            "enabled": true,
#            "name": "bond1"
#        },
#        {
#            "enabled": true,
#            "name": "lo"
#        },
#        {
#            "description": "Configured by Ansible Network",
#            "duplex": "full",
#            "enabled": true,
#            "name": "eth3",
#            "speed": "100"
#        },
#        {
#            "description": "Configured by Ansible",
#            "duplex": "full",
#            "enabled": false,
#            "mtu": 600,
#            "name": "eth2",
#            "speed": "100"
#        },
#        {
#            "description": "Configured by Ansible Network",
#            "duplex": "full",
#            "enabled": true,
#            "name": "eth1",
#            "speed": "100"
#        },
#        {
#            "description": "Outbound Interface for this appliance",
#            "duplex": "auto",
#            "enabled": true,
#            "name": "eth0",
#            "speed": "auto"
#        }
#    ]
#
# "commands": [
#        "delete interfaces bonding bond1 description",
#        "delete interfaces ethernet eth1 speed",
#        "delete interfaces ethernet eth1 duplex",
#        "delete interfaces ethernet eth1 description",
#        "delete interfaces ethernet eth2 speed",
#        "delete interfaces ethernet eth2 disable",
#        "delete interfaces ethernet eth2 duplex",
#        "delete interfaces ethernet eth2 disable",
#        "delete interfaces ethernet eth2 description",
#        "delete interfaces ethernet eth2 disable",
#        "delete interfaces ethernet eth2 mtu",
#        "delete interfaces ethernet eth2 disable",
#        "delete interfaces ethernet eth3 speed",
#        "delete interfaces ethernet eth3 duplex",
#        "delete interfaces ethernet eth3 description"
#    ]
#
# "after": [
#        {
#            "enabled": true,
#            "mtu": 1300,
#            "name": "bond0"
#        },
#        {
#            "enabled": true,
#            "name": "bond1"
#        },
#        {
#            "enabled": true,
#            "name": "lo"
#        },
#        {
#            "enabled": true,
#            "name": "eth3"
#        },
#        {
#            "enabled": true,
#            "name": "eth2"
#        },
#        {
#            "enabled": true,
#            "name": "eth1"
#        },
#        {
#            "description": "Outbound Interface for this appliance",
#            "duplex": "auto",
#            "enabled": true,
#            "name": "eth0",
#            "speed": "auto"
#        }
#    ]
#
#
# ------------
# After state
# ------------
#
# vyos@vyos:~$ show configuration commands | grep interfaces
# set interfaces bonding bond0 mtu '1300'
# set interfaces bonding bond1
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 address 'dhcpv6'
# set interfaces ethernet eth0 description 'Outbound Interface for this appliance'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 hw-id '08:00:27:ea:0f:b9'
# set interfaces ethernet eth1 smp-affinity 'auto'
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth2 smp-affinity 'auto'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces loopback lo
#
#

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key	Returned	Description
after list	when changed	The configuration as structured data after module completion. Sample: The configuration returned will always be in the same format of the parameters above.
before list	always	The configuration as structured data prior to module invocation. Sample: The configuration returned will always be in the same format of the parameters above.
commands list	always	The set of commands pushed to the remote device. Sample: ['set interfaces ethernet eth1 mtu 1200', 'set interfaces ethernet eth2 vif 100 description VIF 100']

Status

This module is not guaranteed to have a backwards compatible interface. [preview]
This module is maintained by the Ansible Network Team. [network]

Red Hat Support

More information about Red Hat’s support of this module is available from this Red Hat Knowledge Base article.

Authors

Nilashish Chakraborty (@nilashishc)

Hint

If you notice any issues in this documentation, you can edit this document to improve it.

© 2012–2018 Michael DeHaan
© 2018–2019 Red Hat, Inc.
Licensed under the GNU General Public License version 3.
https://docs.ansible.com/ansible/2.9/modules/vyos_interfaces_module.html