W3cubDocs

/Ansible 2.9

ce_sflow – Manages sFlow configuration on HUAWEI CloudEngine switches

New in version 2.4.

Synopsis

  • Configure Sampled Flow (sFlow) to monitor traffic on an interface in real time, detect abnormal traffic, and locate the source of attack traffic, ensuring stable running of the network.

Parameters

Parameter Choices/Defaults Comments
agent_ip
-
Specifies the IPv4/IPv6 address of an sFlow agent.
collector_datagram_size
-
Specifies the maximum length of sFlow packets sent from an sFlow agent to an sFlow collector. The value is an integer, in bytes. It ranges from 1024 to 8100. The default value is 1400.
collector_description
-
Specifies the description of an sFlow collector. The value is a string of 1 to 255 case-sensitive characters without spaces.
collector_id
-
    Choices:
  • 1
  • 2
Specifies the ID of an sFlow collector. This ID is used when you specify the collector in subsequent sFlow configuration.
collector_ip
-
Specifies the IPv4/IPv6 address of the sFlow collector.
collector_ip_vpn
-
Specifies the name of a VPN instance. The value is a string of 1 to 31 case-sensitive characters, spaces not supported. When double quotation marks are used around the string, spaces are allowed in the string. The value _public_ is reserved and cannot be used as the VPN instance name.
collector_meth
-
    Choices:
  • meth
  • enhanced
Configures the device to send sFlow packets through service interfaces, enhancing the sFlow packet forwarding capability. The enhanced parameter is optional. No matter whether you configure the enhanced mode, the switch determines to send sFlow packets through service cards or management port based on the routing information on the collector. When the value is meth, the device forwards sFlow packets at the control plane. When the value is enhanced, the device forwards sFlow packets at the forwarding plane to enhance the sFlow packet forwarding capacity.
collector_udp_port
-
Specifies the UDP destination port number of sFlow packets. The value is an integer that ranges from 1 to 65535. The default value is 6343.
counter_collector
-
Indicates the ID list of the counter collector.
counter_interval
-
Indicates the counter sampling interval. The value is an integer that ranges from 10 to 4294967295, in seconds. The default value is 20.
export_route
-
    Choices:
  • enable
  • disable
Configures the sFlow packets sent by the switch not to carry routing information.
forward_enp_slot
-
Enable the Embedded Network Processor (ENP) chip function. The switch uses the ENP chip to perform sFlow sampling, and the maximum sFlow sampling interval is 65535. If you set the sampling interval to be larger than 65535, the switch automatically restores it to 65535. The value is an integer or 'all'.
rate_limit
-
Specifies the rate of sFlow packets sent from a card to the control plane. The value is an integer that ranges from 100 to 1500, in pps.
rate_limit_slot
-
Specifies the slot where the rate of output sFlow packets is limited. If this parameter is not specified, the rate of sFlow packets sent from all cards to the control plane is limited. The value is an integer or a string of characters.
sample_collector
-
Indicates the ID list of the collector.
sample_direction
-
    Choices:
  • inbound
  • outbound
  • both
Enables flow sampling in the inbound or outbound direction.
sample_length
-
Specifies the maximum length of sampled packets. The value is an integer and ranges from 18 to 512, in bytes. The default value is 128.
sample_rate
-
Specifies the flow sampling rate in the format 1/rate. The value is an integer and ranges from 1 to 4294967295. The default value is 8192.
sflow_interface
-
Full name of interface for Flow Sampling or Counter. It must be a physical interface, Eth-Trunk, or Layer 2 subinterface.
source_ip
-
Specifies the source IPv4/IPv6 address of sFlow packets.
state
-
    Choices:
  • present ←
  • absent
Determines whether the config should be present or not on the device.

Notes

Note

  • This module requires the netconf system service be enabled on the remote device being managed.
  • Recommended connection is netconf.
  • This module also works with local connections for legacy playbooks.

Examples

---

- name: sflow module test
  hosts: ce128
  connection: local
  gather_facts: no
  vars:
    cli:
      host: "{{ inventory_hostname }}"
      port: "{{ ansible_ssh_port }}"
      username: "{{ username }}"
      password: "{{ password }}"
      transport: cli

  tasks:
  - name: Configuring sFlow Agent
    ce_sflow:
      agent_ip: 6.6.6.6
      provider: '{{ cli }}'

  - name: Configuring sFlow Collector
    ce_sflow:
      collector_id: 1
      collector_ip: 7.7.7.7
      collector_ip_vpn: vpn1
      collector_description: Collector1
      provider: '{{ cli }}'

  - name: Configure flow sampling.
    ce_sflow:
      sflow_interface: 10GE2/0/2
      sample_collector: 1
      sample_direction: inbound
      provider: '{{ cli }}'

  - name: Configure counter sampling.
    ce_sflow:
      sflow_interface: 10GE2/0/2
      counter_collector: 1
      counter_interval: 1000
      provider: '{{ cli }}'

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key Returned Description
changed
boolean
always
check to see if a change was made on the device

Sample:
True
end_state
dictionary
verbose mode
k/v pairs of configuration after module execution

Sample:
{'agent': {'family': 'ipv4', 'ipv4Addr': '1.2.3.4', 'ipv6Addr': None}}
existing
dictionary
verbose mode
k/v pairs of existing configuration

Sample:
{'agent': {}}
proposed
dictionary
verbose mode
k/v pairs of parameters passed into module

Sample:
{'agent_ip': '6.6.6.6', 'state': 'present'}
updates
list
always
commands sent to the device

Sample:
['sflow agent ip 6.6.6.6']


Status

Authors

  • QijunPan (@QijunPan)

Hint

If you notice any issues in this documentation, you can edit this document to improve it.

© 2012–2018 Michael DeHaan
© 2018–2019 Red Hat, Inc.
Licensed under the GNU General Public License version 3.
https://docs.ansible.com/ansible/2.9/modules/ce_sflow_module.html